How to Build a Shed Door

how to build a shed door

Build a Shed Door that will last

The shed door seldom gets the maximum amount attention as would the roof and even the foundation, most of the time folks would simply purchase a pre built door, measure it and install it and think that the job is done. But since the shed door is the single part of the shed that gets the most action, it’s highly likely that it would be the first storage shed item to receive damage. And with storage sheds, the door can vary a whole lot in terms of size and the way it opens. Depending on what you plan to keep inside your shed, you may either need a small sized door or one where a small garden tractor can pass through.


Most storage sheds though are used for keeping large tools like a wheel barrow or a grass cutter, so it is inevitable that one day it may either break off its hinges or develop a big hole because of the occasional banging and hitting of your equipment. So it’s important to have a sizeable shed door that will accept your largest size machine. And to confirm that your door can continue to handle wear and tear you’ve got 2 choices once on how to build a shed door, the ledged door and therefore the ledged embraced door.


The first thing that you need to do is to ensure that you have all the tools that you will need before you learn how to build a shed door. The tape measure is your best friend. It is important that your door fits like a glove on its frame. Take into account the small space that your hinges will occupy. You don’t want a shed door that is not leveled. The top half may either be hitting the frame and there’s a gap on the lower half, or vice versa. Not only will you not be able close your door and lock it properly, but you can also cause damage to your door frame.


When choosing lumber to use for building your shed door, you can either use a rough cut or a finish cut. But what is important is that the lumber is already completely dry; if not, there can be shrinkage in the future when the wood loses its moisture. Usually, lumber that is 1 inch thick is used. Some diy shed builders choose to use green or brown treated wood when deciding on how to build a shed door.


After doing your measurements, you can now use your saw to cut your boards. After cutting, lay down all your boards, put them together and make your final measurement. You should now cut the lumber you will use for your braces. Typically a door brace would need three pieces of lumber, one goes across the top side of the door, one on the bottom side and one longer piece to go across diagonally the length of the door making a Z-shape. Nail or glue them all together.
Now you can measure the hinges on your door jamb and to your shed door. You can now just screw in the hinges and your door is done. If you want to put a handle or a gate latch, you can do so before attaching the door to its frame.

How to Build a Shed Ramp the Right Way

How to Build a Shed Ramp

How to Build a Shed Ramp

A shed ramp is extremely important to any shed that you want to store any type of small riding lawn mower or maybe even a bigger machine like a riding lawn tractor. A ramp can be beneficial in moving your equipment in and out of your shed.  This is a vital part when learning how to build a shed ramp for any backyard garden or barn shed. You also need to make sure that your ramp will work to your advantage you need to build it properly.

There are two main things to consider for your shed ramp plans. Size and slope. Make sure to consider these when building a garden shed ramp. Along with slope and size, there are a few other factors needed when learning how to build a shed ramp.

Only $37 for 12,000 shed plans

Here are those factors.

The slope of the ramp – double-check the location of your backyard storage shed. You don’t want to build a shed and later find out that the storage shed ramp won’t fit. The length of your ramp relies on the slope that you just have chosen. Choosing the slope of your ramp is extremely important as this can be the determinant of the convenience of use and its safety.  It is also imperative that you plan the slope well and consider what type of equipment will be used on the shed ramp.

Safety – a poorly planned steep slope would clearly create problems for you to defy gravity, once you start moving your machinery in and out of the garden shed.  If you’re pushing a heavy mower up a steep ramp, there is a greater chance that you might slip and get crushed. Safety needs to be an important factor when building a shed ramp. Besides, building codes need to be considered. Most require an 8 to 1-inch slope. Besides building codes on how to build a shed ramp, also research other codes at your local city office.

Ease of use – while most ramps don’t need to support a car or truck, but you still need to build the shed ramp to support your riding lawn mower like mentioned earlier.  You may start to think that having a reasonably smart slope and enough driving area would be enough, that isn’t the case.  Many of those machines have low hanging mower decks that may hang up on way into the storage shed. Just one more thing to think about when considering how to build a shed ramp.

The surface of the ramp – be aware of the surface of the wood, steel, or concrete, rain, and other factors may cause your ramp to become slippery thus increasing the risk of accidents. To prevent this, use rubberized flooring or anti-slip paint can help decrease the risk of falling on your shed ramp. Galvanized wire or custom metal sheets with dull spikes can even facilitate to increase the slip resistance of your ramp.

These are the most important essential factors that you just must always bear in mind when building a shed ramp. Include this in your shed ramp plans so that you will not forget about any of these shed ramp tips.

Just like when you use safety glasses around power tools, your new storage shed ramp needs to fit the needs of your machines you will be storing in the shed.

shed ramp plans

While your outdoor garage is getting cramped, it’s time to have a storage shed along with a shed ramp for storing yard tools, gardening supplies, pool chemicals, and other outdoor equipment. But as most permanent storage sheds are placed on a foundation pad or footing, you get a level difference of 9 to 14 inches above the ground.

Hence, building a shed ramp is essential when you need to get heavy garden machinery and riding movers in and out of the storage shed. It makes loading and unloading of heavy equipment from your shed or garage safe and easy thereby reducing the risk of accidents.

So here is a brief guide and tips on how to build a ramp for a shed:

Why do I need a shed ramp?

Before you can have your storage shed placed, you prepare a solid leveled base including gravel or crushed stone with either treated wood foundations or concrete foundation blocks. For large sheds, you require strong foundations to uniformly transfer the load.

Similarly keeping in view the overall topography of the area you can’t place storage sheds directly on the ground. So, due to the level difference of the floor level with the adjacent ground level you have to build a storage shed ramp of suitable length and slope provision for safe and stress-free movement of heavy equipment in and out of the garage. 

How long should I make the shed ramp?

Choosing the length and slope of the shed ramp is a very important part of your shed planning for getting the maximum benefit out of it. Whether your using shed ramp plans or have your own shed ramp ideas, an ideal shed ramp will have a shallow slope and excess length for ease of use. But you have to make sure that there is sufficient space available in front of the shed.

How to build a shed ramp with a good slope angle

The slope and length required are governed by the height from the external ground level to the shed floor. Regarding the slope selection here are some recommendations for building a shed ramp:

For public ramps, the steepest slope allowed is 1:12 which means one-inch rise for every 12 inches horizontally. This slope is governed by the ease of use for wheelchair users.

For general public buildings, the recommended maximum slope is 1:8 which means one-inch rise for every 8 inches horizontally. So, if you go with 1:8 and your floor level difference is 12 inches, the required length of the ramp will be 8 feet.

If you don’t have that much longer available you can go steeper up to about 1:4 but it will increase the risk of slipping so you have to make adjustments accordingly. You can use anti-slip paint or staple down the metal sheet with the ramp surface.

Regarding the width of the ramp for the shed, you should at least provide six inches wider ramp on both sides of your door openings. This will make it easy for the machines to move in and out.

 How to build a ramp for a shed?

Now to start you need to provide a ledger board by mounting it flush with the face of the shed floor. You may have to rip off the framing of the shed if it lips underneath the door. A Ledger board of 2×6 inches is commonly used that can be anchored underneath the shed door with lag screws and washers.

Shed ramps on the ground at the proper angle.

The next step is to mark the area of the shed ramp on the ground, keeping in view the length you selected in the previous step. Measure the distance from the face of the shed and dig holes for the supporting concrete blocks underneath the ramp.

Shed ramps on blocks to protect the joists

After fixing the concrete blocks you now have to measure and cut stringers. Measure the distance from the far edge of the concrete blocks and the ledger board. Cut the stringers up to this much length and secure each stringer with screws into the ledger board.

Shed ramps should have proper joists spacing

Keeping in view the spacing between the stringer, you may have to provide a spacer in between the stringers. So, cut the blocks and screw them between the stringer. The last step is to cut the ramp boars to length, predrilled holes, and screwed the boards with the stringers.

Make sure to secure the ramp boards properly with the stringer and into the concrete (using concrete anchors).